EF70-300mm f/4-5.6 IS USM
ENG
Instruction
a Safety Precautions
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
againsharmful interference in a residential installation. This
uipment generates, uses and can radiate radio frequency
ergy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
a Safety Precautions
• Do not look at the sun or a bright light source
through the lens or camera. Doing so could result
in loss of vision. Looking at the sun directly through
the lens is especially hazardous.
• Whether it is attached to the camera or not, do
not leave the lens under the sun without the
lens cap attached. This is to prevent the lens from
concentrating the sun’s rays, which could cause a
fire.
Handling Cautions
• If the lens is taken from a cold environment into
a warm one, condensation may develop on the
lens surface and internal parts. To prevent
condensation in this case, first put the lens into an
airtight plastic bag before taking it from a cold to
warm environment. Then take out the lens after it
has warmed gradually. Do the same when taking
the lens from a warm environment into a cold one.
• Do not leave the lens in excessive heat such as in
a car in direct sunlight. High temperatures can
cause the lens to malfunction.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for
help.
This Class B digital apparatus complies with Canadian ICES-003.
ENG-2
Nomenclature
Image stabilizer mode selector switch (→ 7)
Hood mount (→ 5)
Zoom position index (→ 5)
Focus mode switch (→ 4)
Filter mounting
thread (→ 10)
Focusing ring (→ 4)
Zoom ring (→ 5)
Contacts
(→ 4)
Image stabilizer switch (→ 7)
Zoom ring
lock lever (→ 6)
Lens mount index (→ 4)
For detailed information, reference page numbers are provided in parentheses (→ **).
ENG-3
1. Mounting and Detaching the Lens
2. Setting the Focus Mode
See your camera’s instructions for details on
mounting and detaching the lens.
To shoot in autofocus (AF) mode, set the focus
mode switch to AF.
To use only manual focusing (MF), set the focus
ode switch to MF, and focus by turning the
focusing ring.
¡After detaching the lens, place the lens with the
rear end up to prevent the lens surface and
electrical contacts from getting scratched.
¡If the contacts get soiled, scratched, or have
fingerprints on them, corrosion or faulty
connections can result. The camera and lens
may not operate properly.
¡Do not touch the rotating parts of the lens while
autofocus is active.
¡Do not adjust focus manually when the focus
mode switch is set to AF.
¡If the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
¡If you remove the lens, cover it with the dust
cap. To attach it properly, align the lens mount
index and the
K
index of the dust cap as shown
in the diagram, and turn clockwise. To remove it,
reverse the order.
ENG-4
3. Hood (Sold separately)
4. Zooming
The ET-65B hood can keep unwanted light out of To zoom, turn the lens’ zoom ring.
the lens, and also protects the front of the lens
Be sure to finish zooming before focusing.
Changing the zoom ring after focusing can affect
the focus.
from rain, snow, and dust.
Attach and align the hood to the hood mount on
the front of the lens, and turn the hood as show
by the arrow to secure it.
The hood can be reverse-mounted on the lens
for storage.
¡The front end of the lens rotates, so hold it when
attaching the hood.
¡Part of the picture may be blocked if the hood is
not attached properly.
¡When attaching or detaching the hood, grasp
the base of the hood to turn it. To prevent
deformation, do not grasp the rim of the hood to
turn it.
ENG-5
5. Fixing the Zoom Ring
The zoom ring can be fixed to keep the lens at the shortest point. This function is convenient for
carrying a camera on a strap because it prevents the lens from extending.
Turn thzom ring to
Slide the zoom ring
1the wideposition
2lock lever in the
(70mm).
direction indicated by
the arrow.
¡To release the zoom ring,
slide the zoom ring lock
lever in the direction
opposite to the arrow.
The zoom ring can only be locked at maximum wide angle.
ENG-6
6. Image Stabilizer
You can use the image stabilizer in AF or MF mode.
Set the STABILIZER
Select the stablizer
When you press the
1switch to
2mode.
3shutter button halfway,
.
¡If you are not going to
use the image stabilizer
function, set the switch to
.
¡MODE Corrects
vibrations in all
directions. It is mainly
effective for shooting still
subjects.
¡MODE 2: It compensates
for vertical camera shake
during following shots in
a horizontal direction,
and compensates for
horizontal camera shake
during following shots in
a vertical direction.
the Image Stabilizer
will start operating.
¡Make sure the image in
the viewfinder is stable,
then press the shutter
button the rest of the way
down to take the picture.
ENG-7
7. Tips on Using the Image Stabilizer
The image stabilizer in this lens is effective for hand-held shots under the following conditions.
● MODE 1
● MODE 2
¡In semi-darkened areas such as indoors or
outdoors at night.
¡When panning subjects in motion.
¡In locations where flash photography is
prohibited, such as art museums and theater
stages.
¡In situations where your footing is uncertain.
¡In situations where fast shutter settings cannot
be used.
ENG-8
Tips on Using the Image Stabilizer
¡The Image Stabilizer cannot compensate
for a blurred shot caused by a subject that
moved.
¡With the EOS-1V/HS, 3, 30/33/Elan7/7E,
30V/33V/Elan7N/7NE, Elan ll/Elan ll
E/50/50 E, 300/Rebel2000, IX, and D30,
the Image Stabilizer will not work during
self-timer operation.
¡Set the STABILIZER switch to
when
you are taking pictures using the Bulb
setting (long exposures). If the
STABILIZER switch is set to
, the
image stabilizer function may introduce
errors.
¡The Image Stabilizer might not be fully
effective in the following cases:
• You shoot while riding on a bumpy road.
• You move the camera dramatically for a
panning shot in Mode 1.
• You shoot using techniques other than
following shots in Mode 2.
¡The Image Stabilizer consumes more
power than normal shooting, so fewer
shots can be taken if you use the
function.
¡When you use a tripod, the Image
Stabilizer should be turned off to save
battery power.
¡The stabilizer is equally effective for hand-
held photography and photography with a
monopod.
¡The image stabilizer function also
operates when the lens is used with an
Extension Tube EF12 ll or EF25 ll.
¡Pictures may look distorted after being
taken depending on the camera, but this
doesn't affect shooting.
¡If you set the camera’s Custom Function
to change the assigned button to operate
the AF, the Image Stabilizer will operate
when you press the newly assigned AF
button.
¡The image stabilizer operates for about
two seconds even when your finger is off
the shutter button. Do not remove the lens
while the stabilizer is in operation. This
will cause a malfunction.
ENG-9
8. Filters (Sold separately)
9. Extension Tubes
(Sold separately)
You can attach filters to the filter mounting thread You can attach Extension Tube EF12 II or EF25
on the front of the lens.
II for magnified shots. The shooting distance and
magnification are shown below.
¡The front end of the lens rotates, so hold it when
attaching the filter.
Camera-to-Subject
Magnification
Distance (mm)
¡Only one filter may be attached.
¡If you need a polarizing filter, use the Canon
Circular Polarizing Filter (58mm).
¡To adjust the polarizing filter, first remove the
lens hood.
Near
584
Far
638
Near
0.22×
0.32×
0.40×
0.39×
Far
70mm
0.17×
0.04×
0.38×
0.09×
EF12 II
F25 II
300mm 1361
70mm 420
300mm 1254
7629
428
3890
Manual focusing is recommended for accurate
focusing.
ENG-10
10.Close-up Lenses
(Sold separately)
Attaching a 250D or 500D (58mm) Close-up
Lens enables close-up photography.
The magnification will be as follows:
¡Close-up Lens 250D:
Can be used at the 70mm end (magnification
0.29x - 0.38x)
¡Close-up Lens 500D:
Can be used (magnification 0.14x - 0.90x)
Manual focusing is recommended for accurate
focusing.
ENG-11
Specifications
Focal Length/Aperture
Lens Construction
Minimum Aperture
Angle of View
70-300 mm f/4-5.6
10 groups, 15 elements
f/32-45
Diagonal: 34° - 8° 15’ Vertical: 19° 30’ - 4° 35’ Horizontal: 29° - 6° 50’
Min. Focusing Distance
Max. Magnification
Field of View
1.5 m/4.9 ft.
0.26 × (at 300 mm)
approx. 394 × 596 mm - 92 × 136 mm/15.5 × 23.5 inch - 3.6 × 5.4 inch (at 1.5 m)
Filter Diameter
58 mm/2.3 inch
Max. Diameter and Length
Weight
76.5 × 142.8 mm/3.0 × 5.6 inch
630 g/22.2 oz
Hood / Lens Cap / Case
Hood
Lens Cap
Case
ET-65B
E-58U
LP1222
¡The lens length is measured from the mount surface to the front end of the lens. Add 21.5 mm when including
the lens cap and dust cap.
¡The size and weight listed are for the lens only, except as indicated.
¡The EF1.4X II/EF2X II extenders cannot be used with this lens.
¡Aperture settings are specified on the camera. The camera automatically compensates for variations in the
aperture setting when the camera is zoomed in or out.
¡All data listed is measured according to Canon standards.
¡Product specifications and appearance are subject to change without notice.
ENG-12
CT1-7560-006
© CANON INC. 2005
2009.7
|